MSRP: $159.00 USD | Product # 8000138 | Buy Online
For most any rails you have on your vehicle, the RailGrab does just what it's name implies. It grabs onto your rails and refuses to let go.
MSRP: $159.00 USD | Product # 8000138 | Buy Online
For most any rails you have on your vehicle, the RailGrab does just what it's name implies. It grabs onto your rails and refuses to let go.
Q: What else is needed to complete a basic rack set up?
A: Just crossbars and lock cores. Check the Fit List to find the correct length crossbar. Locks are not required, but a really good idea.
Q: Is there a way I can make the towers taller?
A: There is no way to make the towers taller.
Q: What sort of maintenance should I perform?
A: Performing maintenance is always a good idea to protect your car and make your rack system last longer. Lubricate nuts, screws, or bolts with grease. Lubricate locks with graphite. Remove the rack when not in use, or at least periodically to clean the pads and the vehicles roof. Clean the rack periodically, especially in marine environments and where road salt is used.
Q: How do I know if the towers are installed correctly?
A: Check the safety steps in the RailGrab instructions. These guidelines will help you determine if the installation is correct.
Q: Will the rack make a lot of noise?
A: Maybe. Wind noise is hard to predict, but it is more often an issue when the rack has little or no load. We make two products, the Fairing and Windjammer, to help control this situation. Large loads tend to dampen noise also. If you have a sunroof the fairing is a good way to help control air flow.
Q: Will it damage my car?
A: We take fitting cars very seriously, and do everything we can to minimize any effect our rack may have on your cars. However, anything coming into contact with a car’s finish, our racks included, will have some effect over time, and some cars are more prone to these issues than others. So where the possibility of such issues is predictable, we make note of that in the Fit List. When the rack will not be in use for an extended period, it is a good idea to take the rack off of the car. You can also do a lot for yourself by: (1) Making sure the car is clean and well waxed prior to installing the rack, (2) Following all instructions for installation and usage, and (3) avoiding situations, like car washes, where the rack may be impacted.
Q: Do I need any Tools to install the towers?
A: Yes, but they are included right inside of the tower.
MSRP: $159.00 USD
Product#: 8000138
Set of 4 towers, attach load bars to factory raised or flush siderails.
Produced: 2009 to present
History: No changes since introduction. Replaced the LowRider, LowRider Max and Locking EZ Rider
General Information: Ships with two complete claw sets for varying rail sizes. Smaller claw pre-installed.
Weight: 0.8lbs. per tower
Dimensions: 4-1/2” wide, 4” tall, 5.5” long
Capacity: Varies by vehicle. Check the Fit List.
 
We are commited to minimizing our impact on the environment.
Click here to learn more »
|
8007026
END CAPS
| 
8880142
RPL, TWR, RAILGRAB
| 
8880143
RPL, WR, HX, 5MM, LNG, RG
|
| 
8880144
RPL, CLW ASSY, LG, RG
| 
8880145
RPL, CLW ASSY, SHRT, RG
| 
8880146
RPL, PAD, CLW, SETS, RG
|
| 
8880147
RPL, PAD, TWR, RG
| 
8880148
RPL, CAP, W/SCR, RG
| 
8880149
RPL, CVR, TWR, RG
|
| 
8880150
RPL, WG ASSY, TWR, RG
| |
|
 |
 
|
